Beko Washing Machine WM Series Rubber Door Seal Gasket- Part No: 2904520100

Product Information

The following DIY repair video should assist you in fitting this part. However the exact procedure may differ depending on your make and model. Peel the seal from the drum and do remember that at the top of the drum there is a small mark that indicates the correct position of the seal. Also using solely liquid detergents, liquid tablets, color only powders (or liquid) as well as most of the "alternative" products like Soap nuts, Eco-balls NOT contain any bleach and will not remove any bacteria effectively. Should you wish to use these alternative products you will also have to add bleach to prevent "greying" of your whites over time as well as other problems. The bacteriological build-up in your machine is due to poor cleaning and damp environment over the days that the machine is not being used. It really is that simple and, all too often down to bad maintenance.

The control panel goes into place by just pressing it against the chassis of the washing machine, and you are ready to fit the screw from the soap drawer. Bear in mind that the door seal may not be the only fault that can cause a leak in your washing machine.Water stains or rust near the door seal meeting the drum or frame suggest a faulty gasket allowing water to leak. A worn gasket leads to more vibration and noise during washing as it can't stabilise the drum effectively and cause increased vibrations. How do you replace a washing machine door seal? If your washing machine is leaking from the front of the door, or the door seal is torn, warped or damaged, or mold has built up at the bottom of the seal and it's beyond cleaning, it´s time to replace it for a new one. After fitting the new seal, inspect it for creases and if its correctly aligned with the top mark of the drum, if needed, just push it yourself to its place (see video for this)

Now we´re ready to fit the new seal, align the seal with the small mark at the top of the drum and the draining holes at the bottom, make sure the seal marks line up on the drum this is very important. The next thing to do is remove the retaining spring that holds the gasket to the drum with the help of a flat blade screw driver What happens is that new type of washing machines use less water to wash and are left for too long without performing a maintenance wash which will allow bacteria to build up in the washing machine which will grow very happily in the warm damp conditions which will eventually lead to what is shown here on the door seal or door rubber as some people call it. Use this genuine door gasket to replace a worn or pierced seal, and to help ensure that your machine is leak-free. Leakages can cause water and scale damage to your appliance and to nearby fixtures, so a working seal is ideal for a well-maintained machine.Unscrew the three screws at the bottom of the facial panel, and now you are ready to release the front facial panel of the chassis. Just slide it downwards and it will come loose easily. Remember that at the top there are small plastic lugs that fit into the panel, don´t lose them! Now the only things you need to do is connect the machine up, select a wash program and slide a piece of paper underneath the washing machine to inspect for any leaks! If you notice that your washing machine produces leaks of water and cleaning product from the front rather than the base of the machine, then there is likely to be a problem with the door seal.

BEKO WM5100S - Ser.No.7148881100; Ser.No.7148881200, BEKO WM5100W, BEKO WM5120S, BEKO WM5120W, BEKO WM5121S, BEKO WM5121W, BEKO WM5140S, BEKO WM5140W, BEKO WM6103W, BEKO WM6120S, BEKO WM6123S, BEKO WM6123W, BEKO WM6133S, BEKO WM6133W, BEKO WM6143S, BEKO WM6143W, BEKO WM6167S, BEKO WM6167W, BEKO WM6355W, BEKO WMC61W, BEKO WMC62W, BEKO WMC64W The next step is to replace the front facial panel of the machine, remember to align the holes with the lugs on the chassis, and don’t forget the little pins at the top! To remove the control panel from the machine you need, with the help of a flat blade screw driver, release the three plastic pins that hold it to the chassis of the machine. Be careful on doing this, because they can easily break, just take your time and do it one by one. When fitting the new seal, it´s a good idea to use a little bit of fairy liquid just to help you slide the seal to its correct position (see video for this), and also with the help of a clamp, secure the seal into its place and then just slowly work around the drum. Make sure that the seal fits correctly on the lip of the drum. It´s a good idea to give a good clean around the outer drum; just wipe all the scale and scum that builds up over time.

Outstanding washing performance