TWILIGHT

Product Information

Use one of the Pure LVT aluminium threshold sectionswherever the floor butts up to a different floor covering and don't forget to allow for the expansion gap. Misuse - No responsibility will be accepted for any damage caused directly or indirectly through misuse, abuse, accident or use that is not consistent with the LiViTLVT installation instructions. No guarantee either express or implied is given for any damage due to inadequate care or other causes including without limitation, stains, damage caused by worn or narrow-heeled shoes, by the movement of furniture or equipment, by heavy items, by impact, by scratches or scarring caused by pets or other animals, by abrasive or sharp-pointed items, or by extreme heat..

Leave Out All The Rest": Published by Universal Music - Z Songs/Chesterchaz Publishing/Big Bad Mr. Hahn Music/Nondisclosure Agreement Music/Rob Bourdon Music/Kenji Kobayashi Music/Pancakey Cakes Music (BMI)/all administered by Universal Music - Z Songs Decode": Published by WB Music Corp. (ASCAP)/But Father, I Just Want To Sing Music (ASCAP)/Josh's Music (ASCAP)/FBR Music (ASCAP), Meaux Hits/Hunterboro Music (ASCAP), Rimutaka Music Publishing (ASCAP)You should now have a gap at the bottom of the door jamb which allows the floor to move freely underneath and which at the same time gives you the expansion gap, now hidden under the door lining. Do NOT under any circumstances pin or glue any skirting or beading to the floor itself. The floor must be allowed to move freely under the skirting and beading at all times. If for some reason you have to switch the underfloor heating off, you must carry out the above process in reverse. Before you start laying your floor or at least before you get too close to the doorway, get an offcut of the floor and the underlay, put them up against the door jamb and then use a handsaw to undercut any architraves and door linings as shown in the diagrams below. Clear out any debris from underneath so the floor can move freely under the door frame once it's installed. Clean your floor regularly. Use a brush or vacuum cleaner first of all to get all the loose dirt off the floor and then use a mop to clean it. Use warm clean water and a mild, pH-neutral detergent or domestic floor cleaning emulsion. Rinse the mop regularly, mop up any residual water and then allow your floor to dry. We strongly recommend using Pure LVT Vinyl Planks cleaning products. Any other cleaning product may contain agents that damage resilient floor surfaces.

Don't forget to allow the same expansion gap around pipes and columns. The easiest way to drill the holes in the floor for radiator pipes is shown in the diagrams above. Line up the floor so that the header joint between two boards is in line with the pipe, join the boards together and mark where the hole should be. Drill the hole, take the boards apart and then slot them together around the pipe. You can then use a radiator pipe coverto cover up the expansion gap.The first and last rows should not be less than 5 cm wide, so measure the room to create a balanced layout and you will then be able to see if the first row needs to be cut to width. If the first row of panels does not need to be trimmed in width, you must remove the tongue on the side of the board that faces the wall to allow for the correct expansion gap. Alternatively you can just measure the gap between the wall and the penultimate row at the middle and both ends of a board, deduct the expansion gap of at least 8mm from your measurements, and then measuring from the tongue side, mark the measurements on the decor-side of the new board. Draw a line connecting all the measurement marks, cut the board along the line you've marked and then snap in two as shown in the video above.

Make sure you remove all traces of plaster, paint, glue, oil, grease, etc. Your subfloor must be clean, flat, dry and stable. Take up any textile floor coverings (such as carpet, needle felts, etc.) and remove all debris including nails. If you're planning to run the floor through the doorway without a break, you will need to cut the door linings and architraves all the way round both door jambs but if you're stopping at the doorway, just cut the linings as far as you're taking the floor. When installing planks, always ensure that the short end joints are staggered by a minimum of 30 cm when you start the next row. Use the left-over piece from the previous row as the first piece of the next row provided that this piece is at least 30 cm long. Alterations or repairs - Alterations and unauthorised repairs to any LiViTLVT flooring will void any and all express or implied warranties including merchantability or fitness for purpose. Any authorised repairs will not extend the guarantee period. Normal variances - Exposure of all or parts of the installed flooring to direct sunlight may cause variations in colour and such variations are not covered by this warrantyAlthough your LiViT LVT floor is one of the easiest floors to maintain, please follow our recommendations below and that way you'll keep it looking fresh as well as protecting the factory finish. After installing your floor, give it an initial cleaning to get rid of any dirt or debris. LiViT LVT floors are carefully inspected by quality control personnel before leaving the factory. However, flooring should be carefully examined by the customer and the installer for any defects prior to installation. In the unlikely event of a defective board being found, it will be replaced free of charge. In the event that a defective board is installed whether inadvertently or deliberately, no warranty shall apply.

Cleaning with this method when the floor looks dirty, or once a week, will maintain your floor adequately. 1. Brush Underfloor heating is fine provided that the floor temperature does not exceed 27°C. Only hot water or electric underfloor heating systems which are embedded in the subfloor floor are suitable. Heating films or other systems that are just placed on the screed or subfloor are not suitable. LiViT LVT is suitable for both residential and commercial areas such as shops, hotel rooms etc, and it's really simple to install! LiViT LVT is laid as a floating floor so there should be no adhesive used between the floor and the underlay or the subfloor. The floor will expand and contract slightly depending on the ambient conditions so you must allow the floor to move freely. You must therefore allow a gap around the edge of the room and any other fixed objects - e.g. radiator pipes, columns, door thresholds etc. Do not screw or nail it down to the subfloor. Exceptionally heavy furniture such as kitchen cabinets must not be installed on top of your floor as again this will prevent your floor from moving freely.LiViTLVT floors have the underlay already attached to the underside of the floor and can be laid directly onto your subfloor. No other underlay should therefore be necessary. Selected items are only available for delivery via the Royal Mail 48® service and other items are available for delivery using this service for a charge. It is vitally important to leave an expansion gap around the edge of the room and around any radiator pipes, columns or door thresholds. This expansion gap should be at least 8mm on all sides and increase 1mm for every metre over 8 metres - e.g. if the room measures 15 metres x 15 metres, the expansion gap should be 15mm.