Cisco SFP-10G-SR= SFP-10G-SR Network Media Converter

Product Information

The Cisco SFP-10G-ZR is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module. It supports link lengths of up to about 80 kilometers on standard Single-Mode Fiber (SMF, G.652). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications. stores threat detection results for use in future analysis. It supports the Advanced Malware Protection (AMP) software feature.

power to the system. If the power switch is in standby position, only the 3.3-V standby power is enabled from the power supply The dual power supplies can supply up to 800-W power across the input voltage range. The load is shared when both power supply The system power requirements are lower than the power supply module capabilities. See the following table. So you have bought an expensive Cisco original brand switch. Now you are considering buying compatible optics for the same. But, do you really need to buy Cisco original brand modules? Amber—Fault detected; power supply not working properly. Includes over voltage, over current, over temperature, and fan failure.

10 GbE SFP+ SR fiber transceiver

of the optical link partner such as how it handles link faults and debounce timing; spanning tree protocol convergence; dynamic When interoperating a Cisco 8-Gbps CWDM SFP Transceiver with a Cisco 4-Gbps CWDM SFP Transceiver, you must manually configure the port speeds.

Each power supply has a separate power cord. Standard power cords or jumper power cords are available for connection to the The Cisco 10GBASE-LRM Module also supports link lengths of 300m on standard Single-Mode Fiber (SMF,G.652).When interoperating a Cisco 4-Gbps CWDM SFP Transceiver with a Cisco 1/2-Gbps CWDM SFP Transceiver, you must manually configure the port speeds on the Cisco 4-Gbps CWDM SFP Transceiver to 1 or 2 Gbps. The Cisco 10GBASE-SR Module supports a link length of 26m on standard Fiber Distributed Data Interface (FDDI)-grade Multimode Fiber (MMF). Using 2000MHz*km MMF (OM3), up to 300m link lengths are possible. Using 4700MHz*km MMF (OM4), up to 400m link lengths are possible. You can use the external Type A USB port to attach a data-storage device. The external USB drive identifier is usbA:. The Type A USB port supports the following:

See Remove and Replace the Fan Tray for the procedure for removing and replacing the fan tray in the Firepower 2130 and 2140. The 100-GB SSD is restricted to the 2110 and 2120 models. The 200-GB SSD is restricted to the 2130 and 2140 models. Do notThe Cisco SFP-10G-ZR-I is a multirate 10GBASE-ZR, 10GBASE-ZW, and OTU2/OTU2e module for industrial operating temperature range. The SFP-10G-ZR-I has a limiting electrical interface receiver, which does not require EDC PHY on the host board, it can be plugged into any SFP+ port. It supports link lengths of up to 70 kilometers on standard Single-Mode Fiber (SMF, G.652), assuming a fiber chromatic dispersion of 20ps/(nm *km). This interface is not specified as part of the 10 Gigabit Ethernet standard and is instead built according to Cisco specifications. The SFP-10G-ZR-I has a cold start at -40⁰C; the transceiver will be operational except optical traffic is not supported from -40⁰ to -28⁰C, all other low speed features (DOM, I2C, etc.) are operational. The module is fully operational from -28⁰C to 85⁰C. The Cisco SFP-10G-SR is in full compliance with the 10G BASE-SR standard. This module has a link length of 26m on the most commonly used standard FDDI- grade multimode fiber. FDDI stands for Fiber Distributed Data Interface. It supports a link length of 300m over OM3 cables and a link length of 400m over OM4 cables. For each network segment that you want to configure inline with fail-open, connect the cables to the paired interface set.

The 1000BASE-BX-D and 1000BASE-BX-U SFPs, compatible with the IEEE 802.3ah 1000BASE-BX10-D and 1000BASE-BX10-U standards, operate on a single strand of standard SMF. The power supply module is rated at 15 A but the system power is limited to 6.1 A. See Hardware Specifications for more system specifications. bypass on this inline interface set. You can only enable hardware bypass on an inline interface set if all the pairs in the shutdown is complete, the console displays It is safe to power off now. The front panel blue locator beacon LED lights up indicating the system is ready to be powered off. You can now move the Apart from the Cisco SFP-10G-LRM module there is another type of module for multimode fibers, called as the SFP-10G-LRM2. This module refers to a type of SFP+ transceiver that are fully compatible with the 10GBASE-LRM standard and have a reach of about 2km over a standard multimode fiber.The GLC-GE-DR-LX SFP also supports Digital Optical Monitoring (DOM) functions according to the industry-standard SFF-8472 Multisource Agreement (MSA). This feature gives the end user the ability to monitor real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias current, and transceiver supply voltage. The following figure shows the Firepower 2130 and 2140 front panel LEDs. Figure 12. Firepower 2130 and 2140 Front Panel LEDs