Sentinel X300 System Cleanser 1Ltr

Product Information

Rapid cleaning may be carried out if Sentinel X400 is used in conjunction with a power-flushing device. litre, 1 300ml aerosol or 1 275ml tube of Sentinel X400 High Performance Cleaner is sufficient to treat a typical domestic system of up to 10 radiators. Larger systems should be dosed with twice this amount. The circulation pump of the system can be used to circulate the Sentinel X300 Cleaner for New Systems solution; however equipment which provides a more rapid circulation can provide a more effective clean. When using an external cleaning rig, the product can be dosed directly to the buffer tank of the rig (follow equipment manufacturer’s instructions).

X300 Cleaner for New Systems is designed to target excess flux residues, greases, and oils in addition to installation debris and sludge. Not only this, but X300 passivates the metal surfaces and helps to prevent copper deposition, a common cause of pinhole corrosion in radiators. Ideally, the product should be added at the first filling of the system. The water should then be circulated at normal operating temperatures for 2 hours before being flushed out. If you are using cold water, leave to circulate for 24 hours. Powerflushing is not necessary when using this product. The system I’m dealing with is not new, but is less than 6 months oldExternal flushing rig: Feed the product in an area of adequate flow in the buffer tank. Follow the machine manufacturer’s instructions. Its formulation also contains agents to ensure the protection of system metals against corrosion during the cleaning as well as preparing the installation for the addition of Sentinel X100 Inhibitor. Recommended dosage: Ideal for pre-dosing, 1 litre of X400 is sufficient to treat a typical domestic system of up to 10 radiators. Circulate from 2 hours to 3 or 4 weeks depending on system fouling.

When using concentrate gel, add directly to the heating system either via a radiator air bleed valve, or via the fill loop using the appropriate adaptor and a suitable caulk gun. Recommended dosage: 1 litre of X800 is sufficient to treat a typical domestic system of up to 10 radiators. For maximum performance circulate from 1-24 hours.X800 is non-aggressive and can be left in the system over 24 hours, however this may cause debris to re-settle reducing effectiveness. Designed for new central heating systems, the Sentinel X300 cleanser flushes out flux installation debris from new indirect central heating systems. This prepares the system for the addition of an inhibitor, which will protect the system components and prolong their effective life and is essential for the prevention of sludge and scale build up. Emulsifiers in the liquid assist in the removal of grease and oils from new radiators. Dispersants lift insoluble flux, metal fillings and dust from the system. A single 1 litre bottle should be plenty to dose about 8 to 10 panels in your radiators. It can be added easily using a dosing vessel or the adaptor supplied. Ensure the system is filled before adding the X300. What next? Add Sentinel X100 inhibitor, to prevent corrosion and the build-up of limescale, the main causes of central heating and boiler inefficiency.Apply to: Restore circulation and effectiveness in systems older than six months that have a significant amount of corrosion debris causing poor circulation and cold spots. Prepare for the installation of new components. Where systems are badly fouled, we recommend a longer circulation period (approximately 3-4 weeks). The product is not aggressive and can be safely left in the system for extended periods. Why? Contamination from the manufacturing and installation processes can accelerate corrosion of new components. According to UK Building Regulations Part L Domestic Heating Compliance Guide, a central heating system should be thoroughly cleaned and flushed out before the installation of a new boiler. It is recommended that Sentinel X400 High Performance Cleaner is used in accordance with standard cleaning and commissioning protocols such as BSRIA Guide “Pre-Commission Cleaning of Pipework Systems” or similar Water Treatment Guidelines from industry organisations such as the Industrial & Commercial Energy Association (ICOM). In this scenario, the system may benefit from a manual flush using with X300. The system I’m dealing with is older than 6 months