ELEGOO Saturn 2 8K 3D Printer, MSLA UV Resin Printer with 10 inch Monochrome LCD, Air Purifier and Screen Protector, 219x123x250mm Larger Printing Size

Product Information

To start with, I loaded my model into Chitubox Pro just as described above and got it sitting at an angled orientation. I oriented with the face pointing away from the build platform so that there would be fewer supports on the face. Leveling the printer was pretty straightforward. The first step is to loosen the two bolts on the sides of the resin tank. Then using the control panel on the front of the printer, you want to raise the build platform to a sufficient height that the resin tank can be removed.

The Saturn INT-19 would have used smaller solid boosters, derived from the first stage of the Minuteman missile, to supplement the thrust of the S-II. Eleven configurations were studied, using between four and twelve solids, with some being started at lift-off, and some being started in flight, and varying propellant loads in the Saturn stages. The S-II stage would have been modified by refitting the J-2–SL engines with reduced expansion ratio nozzles, to increase sea level thrust to 174,400 pounds-force (776kN) per engine. The highest total impulse configuration would have used twelve boosters, with eight started at launch and four started after the first group had been jettisoned. It would have been capable of lofting a payload of 75,400 pounds (34,200kg). [1] To wash the models, I used Elegoo’s largest Wash and Cure station, the Mercury X bundle. Although this was designed with the original Saturn and Saturn S in mind, which have slightly smaller build volumes, I found the build platform still fit into the tank. The only issue I had was with some of the taller prints bottoming out. modulation possibilities. Creating new modulation connections could not be easier: just drag and drop. Larger than Saturn's Printing Volume】With a build volume of 219x123x250mm / 8.62x4.84x9.84 inch and a 10” large mono LCD screen make the prototype size larger and the curing efficiency higher, you can print one larger model or multiple smaller models in a single batch. Saturn 2 includes 12 new distortion styles, a radically overhauled and expanded modulation system, enhanced envelopes, linear phase processing, and a new ‘Superb’ High-Quality mode. The new distortion styles, nearly twice as many, included ‘Subtle’ versions of the Tape, Tube, and Saturation styles for warmth and four new guitar amplifiers, three Transformer styles. All of this means that you use Saturn 2 for everything from sweetening a mix bus through to guitar amp simulation.It doesn't matter whether it's a large-format model or several small objects - with a build volume of 219 x 123 x 250 mm, there are hardly any limits to your creativity! What worked well for me was to start off by washing the item in the water first after printing, then remove the supports while they were still soft. After that, I dipped it in water briefly and used the brush included with the water washable resin to loosen up any more resin residue. I gave it another rinse in the rinse tank in hopes that the water would now be able to get into the nooks to help remove any additional resin. After letting the item completely dry, I then cured it and this prevented any white residue from forming on the prints, which can happen even with the water washable resins. Cleaning Up After a Failed Print on Elegoo Saturn 2 8K a b "Studies of Improved Saturn V Vehicles and Intermediate payload Saturn Vehicles" (PDF). Boeing Space Division. 7 October 1966. Archived from the original (PDF) on June 14, 2006. There was a large payload gap between the Saturn IB's 46,000-pound (21,000kg) low Earth orbit capacity and the Saturn V's 310,000-pound (140,000kg) capability.

Fully redesigned, easy-to-use interface, including a new design of modulation sources and floating slot panel With some of Elegoo’s earlier printers, this guessing has yielded softer prints that were often gouged with the spatula upon removal. It appears that the company has increased the exposure time with the latest test prints, so it takes a bit longer, but the model is less likely to be damaged. AWIN, Sovendus, Meta-Pixel, Google Ads, Microsoft Advertising, creativecdn.com (RTBHouse), Ads DefenderTo test printing a bust, I decided to go with a model of an Elf Archer Bust because the dimensions fit well in this printer and I wanted to see how the details came out. Chitubox has a nice feature that allows you to hollow out the model. It also has a feature to allow you to add drain holes so that you can rinse out any excess resin from inside the head. It also comes with a set of hex key wrenches and some spare screws in case any servicing or repairs need to be performed during the printer’s lifetime. There are two pairs of latex gloves and two surgical style masks for personal protection, but you will probably want to get some higher quality masks and additional gloves for working with resin. The Saturn 2 is equipped with dual linear rails along the Z-axis, which ensure high stability. The movements of the build platform run smoothly. The MSLA 3D printer allows you a Z-axis resolution of up to 0.00125 mm. Prints can and eventually do fail even on resin printers, though I did not experience any failed prints on the Saturn 2 myself. Whether it happens due to support structures that are unable to support the mass or any number of other things, you still will have a mess to clean up before you can print again. The popular Elegoo Saturn gets another new edition: the Elegoo Saturn 2! The successor is equipped with a huge 10-inch 8K monochrome LCD, allowing for even larger and more accurate prints. The huge build volume of this MSLA-3D printer makes it possible to print detailed, large-format objects.